AZDelivery 3 x NodeMCU Amica Modul V2 ESP8266 ESP-12F WiFi WiFi Development Board mit CP2102 kompatibel mit Arduino inklusive E-Book!
16,99 €
Im Home Assistant wird es als 2 Relais mit Symbolen und 2 binären Sensoren (einschließlich Leistung, Strom und Sensoren) angezeigt. Wenn die „max_power“ auf einem Kanal überschritten wird, wird dieser Kanal ausgeschaltet und eine dauerhafte Benachrichtigung wird im HA erstellt. Wenn die „max_temp“ überschritten wird, werden die 2 Kanäle abgeschaltet und eine dauerhafte Benachrichtigung wird im HA erstellt.
substitutions:
devicename: shelly_25
channel_1: Light 1
channel_2: Light 2
max_power: "2000.0"
max_temp: "70.0"
esphome:
name: ${devicename}
platform: ESP8266
board: esp01_1m
wifi:
ssid: "WIFI SSID"
password: "PW"
power_save_mode: none
output_power: 20dB
fast_connect: on
manual_ip:
static_ip: 192.168.178.77
gateway: 192.168.178.1
subnet: 255.255.255.0
# Enable fallback hotspot (captive portal) in case wifi connection fails
ap:
ssid: "NAME"
password: "PW"
captive_portal:
# Enable logging
logger:
level: DEBUG
# Enable Home Assistant API
api:
ota:
web_server:
port: 80
time:
- platform: sntp
id: my_time
i2c:
sda: GPIO12
scl: GPIO14
sensor:
- platform: ade7953
irq_pin: GPIO16 # Prevent overheating by setting this
voltage:
name: ${devicename} voltage
# On the Shelly 2.5 channels are mixed ch1=B ch2=A
current_a:
name: ${channel_2} current
internal: true
current_b:
name: ${channel_1} current
internal: true
active_power_a:
name: ${channel_2} power
id: power_channel_2
# active_power_a is normal, so don't multiply by -1
on_value_range:
- above: ${max_power}
then:
- light.turn_off: lightid2
- homeassistant.service:
service: persistent_notification.create
data:
title: Message from ${devicename}
data_template:
message: Switch turned off because power exceeded ${max_power}W
active_power_b:
name: ${channel_1} power
id: power_channel_1
# active_power_b is inverted, so multiply by -1
filters:
- multiply: -1
on_value_range:
- above: ${max_power}
then:
- light.turn_off: lightid1
- homeassistant.service:
service: persistent_notification.create
data:
title: Message from ${devicename}
data_template:
message: Switch turned off because power exceeded ${max_power}W
update_interval: 30s
- platform: total_daily_energy
name: ${channel_1} energy
power_id: power_channel_1
filters:
# Multiplication factor from W to kWh is 0.001
- multiply: 0.001
unit_of_measurement: kWh
- platform: total_daily_energy
name: ${channel_2} energy
power_id: power_channel_2
filters:
# Multiplication factor from W to kWh is 0.001
- multiply: 0.001
unit_of_measurement: kWh
# NTC Temperature
- platform: ntc
sensor: temp_resistance_reading
name: ${devicename} temperature
unit_of_measurement: "°C"
accuracy_decimals: 1
icon: "mdi:thermometer"
calibration:
b_constant: 3350
reference_resistance: 10kOhm
reference_temperature: 298.15K
on_value_range:
- above: ${max_temp}
then:
- light.turn_off: lightid1
- light.turn_off: lightid2
- homeassistant.service:
service: persistent_notification.create
data:
title: Message from ${devicename}
data_template:
message: Switch turned off because temperature exceeded ${max_temp}°C
- platform: resistance
id: temp_resistance_reading
sensor: temp_analog_reading
configuration: DOWNSTREAM
resistor: 32kOhm
- platform: adc
id: temp_analog_reading
pin: A0
status_led:
pin:
number: GPIO0
inverted: yes
output:
- platform: gpio
pin: GPIO4
id: shelly_25_relay_1
- platform: gpio
pin: GPIO15
id: shelly_25_relay_2
light:
- platform: binary
name: "${channel_1}"
output: shelly_25_relay_1
id: lightid1
- platform: binary
name: "${channel_2}"
output: shelly_25_relay_2
id: lightid2
binary_sensor:
- platform: gpio
pin:
number: GPIO13
name: "${channel_1} input"
on_state:
then:
- light.toggle: lightid1
- platform: gpio
pin:
number: GPIO5
name: "${channel_2} input"
on_state:
then:
- light.toggle: lightid2